Cmg off.nr.1790 data 21.01.2014

S.r.l. Via A. Diaz, 80-82 21057 Olgiate Olona (Varese) Italy Tel: (*39) 0331-37831 Fax: (*39) 0331-378352 e-mail: [email protected]

st

Quotation No.1790

Date: 21 January, 2014

Prepared for:

P.P.H.U. FOL- POL ul. Jozefow 22 99-300 KUTNO POLAND

For attention of:

Mr. Jacek Borowski

Subject:

No.1 Extrusion line type “4530 LHE – DW 700 TA”

CMG S.r.l. Sede legale: Corso Europa, 71 21010 Cardano al Campo (VA) - ITALY Tel: (*39) 0331-37831 Fax: (*39) 0331-378352

Dear Mr. Borowski, thanking you for your interest in our products we herewith have the pleasure to submit our best offer for: No. 1

Extrusion line type 4530/LHE with TA 700/D winder

with following specifications: Space requirement:

as per lay-out drawing to be supplied separately

Standard colour:

grey RAL 7032

Estimated container space needed:

upon Customer’s request

General service requirements Electrical Mains power supply: Maximum allowable supply fluctuation: Total installed power:

400 VAC, + N + E, 50 Hz -10% + 5% as per lay-out drawing to be supplied separately

Cooling water Operating pressure: Maximum allowable pressure fluctuation: Temperature: Hardness: Quality:

2-4 bar +/- 0,2 bar 15-20°C for extruder cooling max. 12 degrees DH biologically and chemically pure

Compressed air Operating pressure: Maximum allowable pressure fluctuation: Quality:

4-6 bar +/- 0,2 bar filtered, dry and oil free

Site environmental conditions All the above specifications are relevant to a site with standard environmental conditions as follows:  In general as dry and dust-free as possible;  Max. geographical elevation 1.000 metres (3,300 ft);  Ambient cooling air temperature from 5 - 30°C (40-85°F). At higher ambient temperatures a cooling air refrigerator is highly recommended;  Ambient humidity as low as possible. At high relative humidity a tropicalised version of the main electrical panel may be necessary;  General ambient temperature max. 40°C (85°F). At higher general ambient temperatures an air conditioning unit has to be provided on the main electrical panel.  If in doubt about any of your local conditions, please contact our technical staff. CMG will not respond to problems with the equipment that arise from ambient conditions beyond our control.

Quotation: 1790

21/01/2014

2

COMPOSITION OF THE LINE

No.1

SINGLE SCREW EXTRUDER TYPE 4530LHE Screw diameter: L/D ratio: Nominal screw RPM range: No. of heating/cooling zones: Barrel heating means: Barrel heating power: Barrel cooling means: Barrel cooling power: Extruder drive: Lubrication pump power: Lubrication flow rate: Cooling water flow rate: Nominal output in LDPE Mfi 1,0:

45 mm 30 : 1 0-210 3 ceramic bands 220 V, single-phase 9 kW centrifugal blowers 1,1 kW 37 kW AC 0,37 kW 9 litres/minute 150 litres/h 80 Kg/h

Extruder base Constructed in steel profile and plate of adequate size to prevent distortions. Provided with wheels with levelling bolts. Gearbox Single screw gearbox with the casing made in grey cast-iron G25, and thrust bearing housing completely integrated; The gears are made of case-steel type 18NiCrMo5, shafts are made in steel type 39NicrMo3 Lubrication system: Splash; Cooling system: Cooling plates Splinded screw connection UNI 221. Screw Barrier type design fabricated in 38CrAlMo7, nitrided and rectified. Hardness 65 - 68 Hrc. Optimised for processing of specified resins and blends. Extruder provided with extraction spindle for screw removal. Barrel Fabricated in 38CrAlMo7 nitrided and rectified. Hardness 65 - 68 Hrc. Provided with grooved feed section. Feed throat block casting in S2 spheroid graphite iron with internal water cooling jacket. Provided with standard resin hopper of 60 litres capacity. Barrel covers Separate top and side panels in sheet stock for easy removal. Hot air exhaust on top cover. The end-user is strongly advised to provide matching thin wall piping to funnel hot air away from the bubble. Electrical connections Connection of all cables (heaters as well as thermo-couples) is done with plugs.

No. 1

SCREEN CHANGER 45 No. of zones: 1 Heating power: 2, 5 kW Lever type screen changer with No. 2 breaker plates.

Quotation: 1790

21/01/2014

3

No. 1

MAIN ELECTRICAL PANEL Completely integrated and pre-wired panel according CE-standards (with CSA certification), in steel metal with double panel for single module for considerable floor-space savings, provided with: No.7 thermoregulation zones. Main thermomagnetic automatic isolator switch; Omron vector open loop inverter for extruder main motor. Omron vector open loop inverter for film cooling blower motor. Single phase 480 VAC solid state relais (Siemens – Gefran – CD automation) Moeller relais, breakers, fuse holders, overloads and push button. Operators panel mounted on site with controls, digital display for machine set reading, single/double action PID thermoregulators (West) and plugs for easy head connection.

No. 1

OSCILLATING BLOWN FILM DIE TYPE BHP 12 R/Z Sizing die range: No. of heating zones: Heating power: Rotation motive power:

50-150 mm 4 10,3 kW 0,37 kW

Die cart Constructed in steel profile with wheels and levelling bolts. Provides mounting for the rotator group and motor. Integrated cooling air manifold for external cooling air manifold. Distributor Constructed in 39NiCrMo3, annealed. Optimised for perfect distribution of the melt into the die body spiral mandrel. Spiral die head Constructed in 39NiCrMo3, annealed. Rheology optimised for indicated resin(s) and blend(s). All surfaces in contact with polymer are hard-chromed to 25 micron. Provided with No.4 adjustable supports for the cooling ring.

No. 1

SIZING DIE For BHP 12 R/Z, diameter 70 mm, LDPE.

No. 1

DOUBLE FLOW COOLING RING TYPE CR 225 Insert range:

70-225 mm

Designed for highest cooling efficiency at a wide BUR-range. Provided with No.6 air inlets with 100 mm diameter. The cooling ring is delivered with air temperature and pressure indicator.

No. 1

COOLING RING INSERT Double flow insert for CR 225, diameter 70 mm LDPE.

No. 1

BLOWER FOR COOLING RING CR 225 Power 5,5 kW AC, provided with inverter.

Quotation: 1790

21/01/2014

4

No. 1

FIXED TAKE-OFF UNIT HO 700 Nominal nip roller width: Useful film passage: Nip roller diameter: Take-off motive power: Line speed range:

700 mm 600 mm 210 mm 1,5 kW AC 0-100 m/min

Take-off unit constructed on a heavy base frame made from steel profile and plate. Nip roller unit with No.1 chrome plated and No.1 neoprene coated cylinder with feedback AC motor reducer. Layflat panels with aluminium idling rollers. Opening and closing is manual. Deep gusseting triangles with manual opening and closing.

No. 1

DOUBLE STATION AUTOMATIC WINDER TYPE TA 700/D Nominal width: Useful film passage: Secondary nip roll diameter: Winding drum diameter: Secondary nip motive power: Winding drum motive power: Line speed range: Maximum roll diameter:

700 mm 600 mm 132 mm 375 mm 1,1kW 1,1kW 0-100 m/min 800 mm

The winder is composed of: Secondary nip roll unit Comprising No.1 driven chromed cylinder and No.1 neoprene coated cylinder with pneumatic opening and closing. Dancer roller system for tension control between haul-off and winder. No. 2 tube slitting knives. No. 2 winding stations back-to-back Each consisting of: Contact winding drum, neoprene coated with diamond pattern to defuse possible trapped air. No.3 web slitting knives. Banana roller before the winding drum. Automatic ready-shaft lay-on for cores 76 mm (3") ID. Automatic film-cut with pneumatic flying knife at pre-set metres. Winding shaft support arms with hydraulic reel off-load. Electrical cabinet On site electrical cabinet mounted on one side of the winder frame. Omron PLC with remote input/output modules for manual and automatic roll change, meter counters set and alarms control. Operator panels with push button, potentiometers, digital display for machine set reading and operator terminal display with function keys for alarms message reading and meter counter setting. Loading cells.

No. 4

PNEUMATIC WINDING SHAFTS Aluminium winding shafts 76 m (3") for TA winder.

Quotation: 1790

21/01/2014

5

No. 1

EXTRUSION TOWER – 4,5 METERS Bolted structure in welded steel profile sub-sections with grid-type platform covering. Provided with stairs and railings according CE-safety requirements.

No. 1

SET OF IDLE ROLLERS

No. 1

BUBBLE GUIDE TYPE RA 700-8-6 CS Layflat range: Installed power:

70 - 710 mm 0.1 kW

Bubble guide with 8 level of 6 articulated arms with Teflon rollers. Motorised diameter adjustment with remote control.

Quotation: 1790

21/01/2014

6

PRICES

Item 1 2 3 4 5 6 7 8 9 10 11 12 13

Q.ty 1 1 1 1 1 1 1 1 1 1 4 1 1

Description Extruder 4530 LHE Lever type screen changer BDL 45 Electrical panel Blowing head type BHP 12R/Z Sizing die diameter 70 mm LDPE Cooling ring type CR 225 Insert for CR 225 diameter 70 LDPE Blower for CR 225 Manual fixed haul off HO 700 Double winder type DW 700 TA Pneumatic steel winding shafts 3" Extrusion tower + set of idle rollers Bubble guide RA 700-8-6 CS Total amount EXW CMG

Unit price 28.448,00 2.825,00 24.495,00 15.516,00 4.470,00 7.139,00 4.021,00 4.298,00 11.812,00 61.168,00 1.081,00 17.629,00 10.717,00 EURO

Price 28.448,00 2.825,00 24.495,00 15.516,00 4.470,00 7.139,00 4.021,00 4.298,00 11.812,00 61.168,00 4.324,00 17.629,00 10.717,00 196.862,00

All prices are indicated in EURO.

SALES CONDITIONS Validity of the offer

: 30 days from issuing date.

Terms of delivery

: ex works CMG.

Delivery time

: 4 months from order, deposit payment and receipt of signed layout.

Installation

: excluded.

Payment terms

: 20% guarantee deposit with the order; 80% prior to shipment.

Quotation: 1790

21/01/2014

7

GENERAL SALES CONDITIONS 1. GENERAL CONDITIONS 1.1 Present general conditions govern every contract concluded with CMG S.r.l. (hereinafter called ‘CMG’ or ‘Vendor’). Any possible modification, even partial, will need to result in writing.

2. VALIDITY OF SALES PROPOSALS 2.1 Every sales proposal (offer/quotation) formulated by the Vendor will have a validity of 30 days from date of emission; after expiration of which and in absence of acceptance by the Buyer, it will automatically loose its validity.

3. CONCLUSION OF THE CONTRACT 3.1 The contract will only be regarded as concluded at the moment of receipt by CMG of the sales proposal as emitted by CMG, duly signed for acceptance by the Buyer. Should however the order originate from the Buyer, the contract will be regarded as concluded the moment latter receives the written acceptance from the Vendor, known as Order Confirmation. 3.2 Any acceptance not integrally conform to a sales proposal and/or order will be regarded as a new proposal or order. 3.3 The order from a Buyer that needs simple and/or necessary specifications with regards to the exact description of the product as ordered (hereinafter called ‘Product’), or the possible signature for acceptance of the general conditions, shall in any case be considered as a binding acquisition by same Buyer. In such a case, the Order Confirmation, issued by the Vendor containing the necessary clarifications, will have to be returned within 15 days duly counter-signed for acceptance by Buyer, solely with the scope to avoid any incorrect interpretation with regards to the course of the contractual relationship. 3.4 Delivery of the Product will be considered to have been contractually effected upon ‘placing at disposal’ of the Buyer. 3.5 Possible modifications to a concluded contract will need to be agreed upon by both parties exclusively in writing.

4. INFORMATION BY MEANS OF PRICE LISTS, CATALOGUES AND ANY OTHER MARKETING MATERIAL 4.1 Price lists, catalogues and any other marketing material only constitute an indication of applicable prices and product type information and as such are not binding for the Vendor.

4.2 All indications/information as provided by aforementioned documentation are given with due diligence and in good faith, however possible errors or omissions contained in same do not constitute any liability for the Vendor.

5. PRICE 5.1 Unless otherwise indicated, contractual prices are intended EXW (Incoterms 2010) CMG S.r.l. – Olgiate Olona - VA - Italy, excluding packaging cost. 6. INVOICE CURRENCY 6.1 Unless otherwise stated, the prices indicated in whatever document and/or correspondence originating from the Vendor are intended in EURO, excluding VAT (Value Added Tax) and any other possible tax, excise or levy. 7. PAYMENT CONDITIONS 7.1 The price shall be paid as follows: a) 20% with the order; b) 80% prior to shipment. 8. ACCEPTANCE TRIALS 8.1 Acceptance trials of the product shall be effected at CMG on a date to be communicated to the Buyer with sufficient notice to enable his personnel to be present (all costs are at Buyer’s charge). The acceptance trials will be regarded successful if and when: a) the Buyer or his personnel, present during the trials, do not specify any reservations on the acceptance protocol in terms of possible defects, or, b) the Buyer declares not to want to assist at the trials, or, in any case, is not present during the trials, and CMG personnel do not specify any reservations on the acceptance protocol in terms of possible defects. In case of negative acceptance trials, CMG will remedy the defects as specified in the acceptance protocol. If the modifications to the product to render same regular are important, the acceptance trials may be repeated with the scope to verify the elimination of the defects as specified in the acceptance protocol. The delivery time will be considered prolonged by a period equal to that necessary to effect the remedies, or in case of a repeated trial, a period equal to the one between the first and consecutive acceptance trials. Being a mere technical execution to guarantee the quality of the product, the acceptance trial shall not constitute delivery of the Product. 9. DELIVERY 9.1 The delivery time shall initiate the moment the down-payment has been received and delivery will be intended as effected (by all effects of legislation, risks included) at CMG with the disposal to the Buyer or to the forwarder or haulage company. 9.2 In case the Buyer does not uplift the Product within 30 days of the disposal - terms considered as mutually agreed - the contract will be regarded as dissolved. In any case the Buyer will be responsible for the daily storing cost of ITL 968.135 (Euro 500). 10 INSTALLATION 10.1 The Vendor may assume responsibility for the installation of the Product, but this duty is not an instrumental element for the conclusion of the sales contract.

Quotation: 1790

21/01/2014

8

10.2 In that case the Buyer shall inform the Vendor within 30 days from the acceptance trials, of the existence of the necessary conditions for installation. 10.3 The Vendor will effect installation with his own personnel and with the supervision of his own specialised technicians, charging the Buyer the relative cost according the valid ASSOCOMAPLAST rates. 10.4 The installation cost may contractually be included in the sales price, however this agreement does not constitute a deviation from the moment of delivery as has been initially agreed.

11 TECHNICAL ASSISTANCE AND OPERATOR TRAINING 11.1 At the conclusion of the sale, upon specific request from the Buyer, the Vendor may be charged with the training of the operator(s) of the Buyer with regards to the use of the Product and its correct maintenance. This training can be effected at Buyer’s site but in this case the time spent by the technicians dispatched by the Vendor shall not exceed 7 days. The daily cost of this service shall be determined on the basis of the valid ASSOCOMOPLAST rates and also all travel and lodging expenses of this personnel shall be reimbursed by the Buyer. 11.2 The Vendor will consequently be available to furnish recommendations and information by means of remote technical assistance but, should this technical assistance result to be insufficient, the Vendor will be obliged to effect specific interventions upon written request of the Buyer and at the conditions as stated under 11.1. 12 GUARANTEE 12.1 The Vendor warrantees the product for a period of 12 months after delivery date. Within this scope the Vendor takes it upon him to replace and/or repair single components free of charge if and when functional defects from the source are encountered, where the cost of shipping and the cost of labour and travel and lodging expenses of the technician(s) will be charged to the Buyer. 12.2 The warranty is void in case the Product will be repaired by un-authorised third parties, in case tools and accessories not approved by CMG are being used or/and non Vendor-approved modifications are being effected. 12.3 The warranty is void in case of damage due to carelessness, negligence in usage, use of products non conform to the characteristics as stipulated in the manual or any other circumstance beyond Vendor’s control. 12.4 The Vendor shall not be held responsible for any other than previewed in the preceding articles and specifically remains excluded from all and any claims for personal and material damage resulting from the use or miss-use of the product and/or resulting from consequential losses. 13. FORCE MAJEUR 13.1 Whenever a party shall not be able to execute the contract for any reason not previewed or not previewable at the time of stipulation of the contract, independently of own free will and of which immediate prove shall be given, same party may suspend the execution of the contract until the ending of the cause of the force major, of which immediate notification shall be given to the other party by registered letter with advise of receipt. It remains understood that upon termination of the force major circumstances, the suspended execution shall have to be executed. 14 TITLE TO THE PRODUCT 14.1 In case payment terms different from those stipulated as per article 7 are agreed upon, it is explicitly agreed that the sale is effected with retention of title to the Product to the Vendor until full settlement of the agreed sales price. Any relative risks will remain however with the Buyer from delivery onwards. Until passing of title to the product the Buyer cannot alienate or otherwise dispose of the Product without the written consent of the Vendor. 15 CONFIDENTIALITY 15.1 All information of technical, commercial and economical nature of which the Parties have come to knowledge at conclusion of the contract shall remain strictly confidential. The Parties will engage in any means to avoid disclosure of any of same. 16 WRITTEN FORM 16.1 In repetition of what has been already stipulated afore, it is established that any and all covenants relative to present contract shall be exclusively concluded and/or approved in writing - also per fax - under penalty of nullification. 17. APPLICABLE LAW AND MEANS OF RESOLVING DISPUTES 17.1 The contract in all effect is governed by Italian law and any dispute shall as a consequence be submitted to the competent judge within the area of jurisdiction of the Vendor. 17.2 The Vendor, at his own discretion, may forgo the competence of Italian legislation and the jurisdiction as previewed above, to act in judgement against the Buyer according the regulations of reconciliation and arbitration of the International Chamber of Commerce in Paris, calling upon three arbitrators nominated conform the aforementioned regulations. The arbitration college will judge according the Lex Mercatoria. Place of arbitration shall be the seat of same CCI: 38, Cours Albert I - 75008 Paris - France; phone: 0033 - 1 - 495 329 4541; fax: 0033 - 1 - 495 329 33. The language of arbitration shall be English. 17.3 In case of doubt the original Italian text will prevail.

_________________ Umberto Daverio CMG S.r.l.

Quotation: 1790

21/01/2014

9

INFORMATIVE AND CONSENT THE TREATMENT OF THE PERSONAL DATA (Art.13 and 23 of the Legislative Decree 196 dated June 30th 2003) Our Company intends to treat the common personal data directly acquired from the party, to which intends eventually to admit data picked up from third-party, deriving essentially from public registers or from knowable documents from anyone. The data can concern: social reason, address, telephone number, fax, e-mail, taxpayer’s code number, VAT registration number, register chamber of commerce, social positions, purchase volumes, qualitative demands, payment terms, banks, turnover, employees number, group one belongs, financial data and of balance, etc… In the course of the picked up data and treated, can also appear sensitive data like agreement and/or membership of trade-union organisation (entrepreneurial associations). Therefore, the party concerned is invited to take vision of the text of the Legislative Decree 196/03, and particularly of the content of the arts. 4-7-8-13-23-26 of the aforesaid one and it declares that regarding the treatment of his/her own personal data has been informed from "COMPANY CMG S.r.l.": a) of the purposes and conditions of the treatment which the data are destined 1) - execution of pre-contract and contract obligations - fulfilment of law obligations connected to administrative dispositions, bookkeeping, fiscal 2)

- location demands and satisfaction degree of the clientele - determination credit, also for possible take out an insurance policy credit - advertising material dispatch, also by mail, fax, e-mail - layout budget and statistics - marketing and references - other functional purpose to the activity of the company

The data will be inserted in the company files and treated in paper form and/or automatized. b) of the nature obligatory or optional of the data contribution The data contribution as in object is obligatory for the purpose of which to the previous point 1), it is optional for the purpose of which to the point 2). c) of the consequences of a possible refusal to answer For the obligatory data, (point 1), impossible execution of the law obligations and of the same contract; for the optional data, (point 2), any consequence. d) of the subjects or of the subjects categories to which the personal data can be communicated and the diffusion range of the same data The data can be communicated to: - Administrations and public Corporate for law obligations - Mother company, checks and connected - Revision companies, certification, control and mayors - Consultation companies that operates for the company in the various sectors - Agents, representatives and distributors for the normal commercial activity - External forwarder for goods delivery and correspondence - Insurance companies, recovery credits companies - Lawyers, advisors Can know the data also subjects named from the company as internal or external responsible person; as well as the employees in the offices: administrative, bookkeeping, commercial, technical, of department, always as entrusted of the treatment. In every case the data won't be spread. e) of the rights as in the art.7 Specifying that the party concerned to which refer the personal data has the right in whatever moment to get the confirmation of the existence or less of the same data and to know the content and the origin, to verify its correctness or to ask the integration or the updating or the rectification of it. To the senses of the same article the right is to ask the cancellation, the transformation in anonymous form or the block of the data treated in law violation, as well as to oppose in every case, for legitimate reasons, to their treatment. f) of the extreme identified… Quotation: 1790

21/01/2014

10

The Holder of the data treatment is: Company CMG S.r.l. "that will treat the data near the own office in: Olgiate Olona Via A. Diaz, 80-82. he Person responsible for the treatment of the personal data is: Dr. Umberto Daverio.

CONSENT TO THE TREATMENT OF THE PERSONAL DATA (Please return to CMG copy of this page duly signed by post or by fax at the No.0039 0331 378352) The undersigned…………………………………. (denomination and social reason for the party concerned, client, supplier, etc.) The person in charge/legal of …………………………………………………………….. With reference to the personal data as in object of the informative above indicated:  expresses the consent to the treatment of common data in the limits and for the purpose indicated  expresses the consent to the treatment of sensitive data in the limits and for the purpose indicated  expresses the consent to the transfer of the data in the countries UE and extra UE in the limits and obligations foreseen by the Legislative Decree 196/03  expresses the consent to the communication of the common and sensitive data, always in the limits and for the purpose indicated

Date…………………………..

Quotation: 1790

Signature……………………………

21/01/2014

11