CSWP Sample Exam 1 Segment 1

Segment 1 of the CSWP Core -This test is made up of a series of problems broken down into sets of questions. Each problem set of questions comes with a description that outlines the problems to be solved for that set. -This section contains 5 questions -You should be able to complete all 5 questions within 90 minutes -Consult answer key after completion of this section

-Initial Part: Create the Part Shown below. Use for Question 1 and 2 -Read following questions before modeling B K

48

10

K

10

D D

M

R5

A

4X 2 X 45 Deg M

Y R2

R2

33 10

8 A

8

C

5X R8

8

SECTION K-K

R10

R2

A C 30 5

SECTION M-M

20

Segment 1 Question 1. Initial part – Stage 1: Build this part in SolidWorks. Unit system: MMGS (millimeter, gram, second) Decimal places: 2 Part origin: Arbitrary Material: 1060 Alloy Density = 2700 kg/m^3 All holes through all unless shown otherwise -Use the following parameters and equations which correspond to the dimensions labeled in the images: A = 84 mm B = 46 mm C = 118 mm D = 27 mm Y= C/2 +20 (To save the most time, make use of linked dimensional values and equations.) (Save each part after every question in a different file, so you can review your work) -Measure the mass of the part. What is the mass of the part (grams)? a. 822 b. 807 c. 791 d. 862

Question 2. Update Parameters of the Initial Part Unit system: MMGS (millimeter, gram, second) Decimal places: 2 Part origin: Arbitrary Material: 1060 Alloy Density = 2700 kg/m^3 All holes through all unless shown otherwise -Use the following parameters and equations which correspond to the dimensions labeled in the images: A = 90 mm B = 45 mm C = 135 mm D = 22 mm Y= C/2 +20 -Measure the mass of the part. What is the mass of the part (grams)?

Modified Part: Create the Part Shown below. Use for Question 3. Note: Modified Dimensions are indicated with inspection bubbles, new dimensions are not. "E" indicates a hole wizard hole at the center of the feature. B

10

K

10

48

D

K D R7 6X 2 X 45 Deg

22

A Y

25

R2

54 R6 X2

40

10

8 E

A

R6 X 6

J

8 20

R2

SECTION K-K

C

8

8

15

J

R2

A

R10

C 45 5

40 SECTION J-J

20

Question 3. Modify the Part Based on New Images Unit system: MMGS (millimeter, gram, second) Decimal places: 2 Part origin: Arbitrary Material: 1060 Alloy Density = 2700 kg/m^3 All holes through all unless shown otherwise -Changes to preexisting geometry are labeled with inspection bubbles. New dimensions are not. Closely examine the dimensions as there are quite a few changes. -Use the following parameters and equations which correspond to the dimensions labeled in the images: A = 92 mm B = 46 mm C = 128 mm D = 24 mm Y= C/2 +20 E= Hole Wizard Standard: ISO Countersink Type: Hex Socket CTSK Head ISO 10642 Size: M6 Fit: Normal Through Hole Diameter: 7.00 mm Counterbore Diameter: 14.00 mm Counter Sink Angle: 90deg End Condition: Through All -Measure the mass of the part. What is the mass of the part (grams)? a. 967 b. 864 c. 924 d. 908

Modified Part: Create the Part Shown below. Use for Question 4 and 5. Note: Modified Dimensions are indicated with inspection bubbles, new dimensions are not. 10

B

48

10

30

15

R1 X 2

15

6 K

K

50

New (x 3)

D

R7

12 6

D

10

25

A

Y R2

6X 2 X 30 Deg

54 R2

30 R4 X 5

R5

8

R6 X2 A

M

36 SECTION K-K

6

R1 X 6

6

6

5

40

48

6

C

8

M R10

8

R2 31

A

C

4

5

20 SECTION M-M

R8 X 5

Question 4. Modify the Part Based on New Images, Again Unit system: MMGS (millimeter, gram, second) Decimal places: 2 Part origin: Arbitrary Material: 1060 Alloy Density = 2700 kg/m^3 All holes through all unless shown otherwise -Changes to preexisting geometry are labeled with inspection bubbles. New dimensions are not. Closely examine the dimensions as there are quite a few changes. -Use the following parameters and equations which correspond to the dimensions labeled in the images: A = 84 mm B = 45 mm C = 120 mm D = 27 mm Y= C/2 +15 Note that the value for Y has changed. -Measure the mass of the part. What is the mass of the part (grams)? a. 655 b. 702 c. 604 d. 581

Question 5. Update Parameters Again Unit system: MMGS (millimeter, gram, second) Decimal places: 2 Part origin: Arbitrary Material: 1060 Alloy Density = 2700 kg/m^3 All holes through all unless shown otherwise

-Use the following parameters and equations which correspond to the dimensions labeled in the images: A = 90 mm B = 48 mm C = 125 mm D = 29 mm Y= C/2 +15

-Measure the mass of the part. What is the mass of the part (grams)?