Indicates where sections should be glued together.Before starting assembly:Writing the number of each section on its back side before cutting out the ...
8 downloads
46 Views
977KB Size
Statue of Liberty, U.S.A.: Assembly Instructions
Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Hiroshi Chiba / PAPERART-C
Before starting assembly:Writing the number of each section on its back side before cutting out the sections is highly recommended. (* This way, you can be sure which section is which even after cutting out the sections.)
http://www.canon.com/c-park/en/ Miniature stand
Indicates where sections should be glued together. Indicates where to insert sections. Do not glue the sections together. Indicates sections that should be glued first, then cut out.
Star-shaped stand Build parts 2 and 4 in the same way.
Choose the stand you like best.
Photo competed model View of completed model
Align and glue the rear surfaces together.
*This model was designed for Papercraft and may differ from the original in some respects.
Assembly Instructions:Six A4 sheets(No.1 to No.6) *Build the model by carefully reading the Assembly Instructions, in the parts sheet page order.
*Hint: Trace along the folds with a ruler and an exhausted pen (no ink) to get a sharper, easier fold.
Attach the reinforcement with glue first.
Align and glue the rear surfaces together.
Fold these parts inward and align and glue their surfaces together.
Assembly Instructions Mountain fold(dotted line)
Make a mountain fold. Valley fold(dashed and dotted line)
Make a valley fold. Scissors line(solid line)
Cut along the line. Cut in line(solid line)
Cut along the line.
Tools and materials Assembly tip Caution
Glue The glue spot(colored dot) shows where to apply the glue.
Glue spot(Red dot)
Glue parts with the same number together. Glue spot(Green dot)
Glue within the same part. Glue spot(Blue dot)
Glue to the rear of the other part.
Scissors, set square, glue(We recommend stick glue), pencil, used ballpoint pen, toothpicks, tweezers, (useful for handling small parts) Before gluing, crease the paper along mountain fold and valley fold lines and make sure rounded sections are nice and stiff. Glue, scissors and other tools may be dangerous to young children so be sure to keep them out of the reach of young children.
Align and glue the rear surfaces together.
Build four identical versions of part 10.
Statue of Liberty, U.S.A.: Assembly Instructions
Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Hiroshi Chiba / PAPERART-C
*Glue the parts together in the sequence shown in steps 1 - 6.
Align and glue the rear surfaces together.
Position the short side on this side
Position the elevator entrance on this side.
Statue of Liberty, U.S.A.: Assembly Instructions
Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Hiroshi Chiba / PAPERART-C
Curve the interior side of this part.
Insert and glue to the rear surface.
View from rear
Position so that the narrower side is located on this side.
* Cover the statue with the upper robe. No gluing is necessary. After positioning the rear surfaces of the side parts together, glue the rear sides of the corners together.
Statue of Liberty, U.S.A.: Assembly Instructions
Cut after gluing the rear surfaces together.
Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Hiroshi Chiba / PAPERART-C
Glue the rear surfaces together.
Glue the rear panels of parts 41 and 43, between which the four sheets of part 42 are sandwiched.
Glue the statue's fingertips here.
Glue to part 29 on the interior side.
Insert and glue the glue tabs to the interior side of this spot.
Fold the fingertips inward and glue to the Declaration of Independence.
Lightly bend this part as shown in the illustration.
Insert to assembled part 47 along this line.
Statue of Liberty, U.S.A.: Assembly Instructions
Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Hiroshi Chiba / PAPERART-C
Miniature stand
*Position in place. No gluing needed.
Finished!
Statue of Liberty, U.S.A.: Assembly Instructions
Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Hiroshi Chiba / PAPERART-C
Star-shaped stand
*Position in place without gluing.
*Place this part on the stand without gluing. Finished!