Fold Guide Optional - Cut out windows (leaving the center rails). Build the window inserts and glue in place behind each window and door opening. Note...
23 downloads
52 Views
5MB Size
Please note that this project is not recommended for children. It requires a moderate degree of skill, and the use of a cutting blade, which is extremely dangerous. When using cutting blades always use protective eyewear. This model was designed to be printed on Matte Paper Heavyweight, and the use of white glue is recommended. Black dashed lines represent a mountain fold (a fold which point upward), and orange dashed lines represent a valley fold (the fold points downward). The orange dashed lines are accompanied by a red “+” at each end. These are to be used as pin guides. Poke small holes at the “+”, flip the sheet over, and score between the holes for a clean valley fold. Read the instructions and study the illustrations carefully before beginning.
A
Optional - Cut out windows (leaving the center rails). Build the window inserts and glue in place behind each window and door opening. Note - “Mother” is in the front, top, left window. Fold Guide
2A
2A 3A
4A
7A
3A
1A
7B
Insert tabs through slots and glue down tabs
5B
5B
8A
Apply a small amount of glue to bottom corners and top edges of roof parts 6A and 6B. Position roof parts so TABS ARE OUTSIDE (see inset)! When roof is in position, glue down tabs.
Score and fold the edges of 5A, 2B and 2C as shown. Apply a small amount of glue to top corners and top edges. Insert tabs through slots of 5A, 2B and 2C. DO NOT GLUE DOWN TABS YET!
6B 6A
2B
2C
Apply a small amount of glue to bottom corners and edges.
Assemble roof parts 6A and 6B.
5A 6B Apply a small amount of glue to top corners and edges.
6A
TABS ARE OUTSIDE!
A free project from http://www.haunteddimensions.raykeim.com
B
4D Assemble tower roof parts 5C and dormer 4D.
Apply a small amount of glue to bottom corners and top edges of tower roof 5C. Position roof parts so TABS ARE OUTSIDE (see inset)! When roof is in position, glue down tabs.
5C 4D
4i
5C
TABS ARE OUTSIDE!
4C 8C Insert tabs in slot then glue down tabs. Apply glue to tabs then insert.
8D 4H
4B x 2
4F & 4G
8E
4F & 4G
4B Attach beneath side door.
4J
8B
4J Attach to side of porch.
6C 4B 6C
Completed Model
6C x 2
1 of 9
1A slots
"Mother" window
3A
4A
Porch 7B here
2 of 9
2A
2C
slots
slots
2B slots
A free project from http://www.haunteddimensions.raykeim.com
3 of 9
3A
Attach piece 2A here A free project from http://www.haunteddimensions.raykeim.com
4 of 9
4C
4i
4H slots
4B
4B
4A 4D
4J
to 3A
4F
4G
A free project from http://www.haunteddimensions.raykeim.com
5 of 9
5B
5C slots
slots
slots
slots
5A
slots
A free project from http://www.haunteddimensions.raykeim.com
6 of 9
6B
slots
6C
6C
6A
Back
slots
slots
slots
slots
slots
Front A free project from http://www.haunteddimensions.raykeim.com
7 of 9
7A
7B
slots
slots
A free project from http://www.haunteddimensions.raykeim.com
8D* 8D
8 of 9
8A
8A*
8C*
8E
8E*
8B* 8B 8C
* for optional transparency printing
A free project from http://www.haunteddimensions.raykeim.com
9 of 9
Front Door
Mother Side Door
Tower front
Optional window inserts A free project from http://www.haunteddimensions.raykeim.com
Tower side